zhlaluminum@gmail.com    +86-18825985370
Cont

Have any Questions?

+86-18825985370

Jun 12, 2017

Anodized And Powder Coated Aluminium Industry Is Widely Used

 Anodized and Powder Coated Aluminium technology as a common surface treatment in the electroplating industry and the main technology, widely used in the electroplating industry. In general, metal members such as aluminum parts, in order to have better surface properties and gloss, most of which have to undergo Anodized and Powder Coated Aluminium process, in its surface covered with a layer of dense and has a certain degree of gloss of the metal oxide film, such as nickel Film and so on. In the anodic oxidation process, a metal such as nickel or the like to be plated is usually used as an anode, and a metal member such as aluminum or the like to be plated is used as a cathode, and the electrons to be metallized at the anode are electrified to nickel ions by electrochemical method, In the electric field under the cover to the metal parts were plated, so as to complete the plating of metal components of the plating process.

In general, it is necessary to degrease the metal member with the acid and alkali before the anodic oxidation step, and after the anodic oxidation, it is necessary to subject the plated metal member to surface sealing treatment. At present, most of the electroplating enterprises use nickel acetate as a sealing agent. In this process, enterprises will produce a lot of degreasing wastewater, acid and alkali waste water and nickel-containing wastewater. These wastes contain a class of contaminated nickel that is strictly controlled by the state and must therefore be properly disposed of before it can be discharged.

Anodized Dyeing Process of Die Casting Aluminum Alloy

The development of the Anodized and Powder Coated Aluminium process of the die-casting aluminum alloy is more difficult than the oxidation process of the ordinary aluminum because the surface properties of the die casting are more complicated, such as the sand hole, the crack, the oxidizing impurity, the release agent and the oil Surface treatment process is often unable to solve the problem, to overcome this problem must be from the die-casting material technology to start, the development of a wide range of stable surface treatment of syrup to overcome this problem, we through a large number of samples, has developed a die-cast aluminum alloy Products are bright, anodized coloring solutions to help customers enhance the competitiveness of their products and enhance the added value of their products!

First, the choice of die-casting materials

Commonly used die-casting aluminum aluminum, aluminum, aluminum, aluminum and zinc alloy. Some people tried to use pure aluminum and components close to 6063 materials for the production of die-casting products, and then do sulfuric acid Anodized and Powder Coated Aluminium process, the small batch of production shows that: die casting after a complex anode treatment, the oxide film layer colorless and transparent, Surface finish can reach the mirror state can be dyed a variety of colors; but the die-casting production of thin-walled, slightly more complex parts of the structure, the phenomenon of cracks is 100% of the existence of almost no longer surface treatment;

ADC12 / ADC10 as the most mature die-casting aluminum alloy, die-casting defects are relatively small, the product performance is relatively stable, coupled with our development of die-casting aluminum alloy chemical polishing agent, is particularly suitable for die casting Anodized and Powder Coated Aluminium pretreatment process, ADC12 / ADC10 staining is possible, suitable for dyeing various colors. In particular, the standard ADC10 die castings have been chemically polished for mirror effect, ADC12 has good machinability but low thermal conductivity! ADC10 is better than ADC12, but the cost is high! In fact, ADC10 is A380 and ADC12 is A383. (ADC12 equivalent to the Chinese-made alloy code YL113, alloy grade is YZAlSi11Cu3, the US alloy grade is 383), ADC10 casting, good pressure, suitable for the manufacture of large die castings. Its mechanical properties and good cutting, but slightly less corrosion resistance. ADC12 and ADC10 compared with the amount of Si, the former 9.6% to 12.0%, the latter 7.5% to 9.5%, the former components in the eutectic point around the alloy of the best mobility, so suitable for die-casting complex castings, its High strength, good pressure resistance, hot brittleness small. ADC12 / ADC10 silicon containing high copper content, the use of ordinary sulfuric acid electrolysis oxidation process and dark gray. The main factors that affect the quality of the appearance are copper, silicon, chromium, iron, zinc, manganese and other metal elements, the metal elements in the aluminum content of the less, after anodic oxidation of the bright and clean the better, The In fact, the appropriate increase in the composition of copper and silicon not only improve the die-casting defects, but also increase the surface of the luster, to improve the uniformity of the fineness of the material, conducive to surface treatment, zinc and magnesium chemical properties of lively should be strictly controlled , Otherwise increase the difficulty of anodic oxidation;

Of course, a reasonable choice of die-casting agent and die-casting molding process parameters, is the casting of anodic oxidation of the necessary conditions.

Second, the pre-treatment process

1, polishing and leveling: the use of mechanical polishing method can be used rough cloth or fine polishing, sandblasting or vibration grinding, magnetic grinding, get flat and bright appearance. There are manufacturers using high-pressure devices will be washed with water and glass sand spray to the surface of the product to achieve the purpose of cleaning and finishing, with remarkable results.

2, in addition to wax: polished after the workpiece in a special cleaning agent to remove the workpiece surface to remove the polishing paste and polishing dirt, but also wash away the workpiece is not attached to a variety of oil.

HTL-210 20-50 g / L TEMP: 50-65 ° C Time: 3-10 min

3, degreasing degreasing alkaline corrosion: to remove the surface of the workpiece oxide, from the type of agent to prevent the product after the throwing fouling;

Degreasing: HTL-310 20-25 g / L TEMP: RT Time: 3-10min

Weakness: HTL-310 50-60 g / L TEMP: 60-75 ℃ Time: 3-5min

4, and in addition: in addition to black and gray

HNO3 (68%) 300-500 ml / L HTL-320 30-50 g / L TEMP: RT Time: 1-3 min

Reaction mechanism: weak erosion after the workpiece to produce a layer of black film, this process can remove the black and gray

5, to immersion HTL-328 stock solution using TEMP: <40 ℃ Time: 1-3min

Completely remove the surface of the workpiece black film, exposed smooth aluminum surface, to prevent impurities into the sewage into the slot

4, chemical polishing (with triacylated relatively low yellow smoke easy to control)

HNO3 (68%) 650-800 ml / L HTL-330 120-150 g / L TEMP: 90-95 ° C Time: 1-3 min

Increase the brightness, reduce the other components outside the aluminum, easy to oxidize the coloring


Send Inquiry